Archives

Desk Shelf / Shed / Woodworking — No Comments
06
Aug 18

Wires and panel

So the walnut panel glueup went as well as I had hoped. The clamps did deform slightly – I need to do that trick of Paul Sellers and stuff them with wood – but the panel came together reasonably well.

There’s a step in the middle where one of the boards bowed though, of just over a mm, so there was some flattening to do before worrying about the surface much.

Ugly. Cross-grain planing required, so out with the #05…

At least it’s easy to see where I’m planing…

That proto-knot there in the back caused some issues with tearout that I’ll have to fix later. But the board is flat to the touch now and was smooth again after a few minutes with the #04 1/2

The chalk’s highlighting areas where even the cabinet scraper wasn’t handing the tear-out because actual lumps had been taken out during the cross-grain flattening. There may be epoxy filling required there, or putting in some inlay to hide it or something.

Also, the sides will be slanted, the shape of the desk is trapezoidal, not rectangular because the sides of the shelves splay outwards (and by the same amount as the sides angle back towards the wall by random chance). I haven’t made the cut yet because I have more boards to prep, and while the board is kicking about on the floor of the shed, that extra material is protecting what will become the edge of the desk.

Incidentally, as the desk is only 17″ off the floor and is for a six-year-old and so forth, I’m not too fussed about the underside…

So the scrub plane was used to get rid of that step on this side, and I didn’t really bother taking down the scallops afterwards. I mean, I gave it a few swipes with the #05 so it’s not “textured”, but I won’t be smoothing it with the #04 or scrapers and I might seal that knot but that’s about it for this side.

Mind you, despite this lack of worry, I’m still miffed at a certain phillips screwdriver…

Yeah, that smug looking git right there in the middle. I was putting away the #04 1/2 and the vibration of seating that back home in the till shook it off the magbar and…

Lousy git of a thing. Well, there’s another site that’ll need inlay…

 

At this point I fixed something small that’s been bugging me for a while. The LED lights I put up in the shed work well, but I hooked them up temporarily while I waited to get the shed properly wired with sockets and such, and I still haven’t gotten to that so all three of them are running into a single cable that plugs into the extension cable that has been running power to the shed as a temporary measure for over two years now…

I mean, for a day or three that’s… well, okay but not great even with cable clips giving the cable some strain relief, but it’s been up for ages because I was busy, so enough already…

Those are wago terminals and a wagobox to house them. I’d never even heard of these until I saw Big Clive’s video on them

I’m so used to terminal blocks that they seemed like overly expensive gimmicky things to me at first, but after the first time you use them, holy crap they’re great. Those are the reusable version (there’s a permanent version that you can technically reuse but nobody does) because I still want to do this right, but this is so much better than the temporary lash-up I had waiting to fall on my head if I kicked the line by accident and run 240V across my scalp. Which, y’know, is suboptimal. So I undid the terminal block and linked everything up with the wago blocks…

And stuffed those into the wagobox and mounted it…

And reran the cable clips and put the cables into the wagobox’s strain relief glands and sealed it all up.

Nice and neat(er) and all working again and no exposed points where you could accidentally grab or poke something and there’s a lot more strain relief on that black mains cable. Much better.

Back to work after the long weekend and a few days’ holidays tomorrow so I’m expecting a long day or two in the office, and then when I get shed time again it’ll be on to the other shelves. Being poplar, they should be both easier working and less pretty than the walnut. Not sure if they have a date with the thicknesser, but if so that’ll be delayed until a Saturday afternoon and I’m not sure how the sides would be done as there’s no way I can run those through the thicknesser inside the shed, there’s just no room; and it’s way too loud to run outside on the decking. They may need to be done by hand with the scrub plane, but at least they’re poplar so it’ll be lighter work.

Desk Shelf / Tools / Woodworking — 3 Comments
05
Aug 18

First chips

So it’s a weekend afternoon so if there’s a more civil time to use a planer, it involves taking a day off work. So to the shed!

First up, fitted the DRO to the planer. Slightly fiddly, and it does still bind a little so I’m sure it needs tweaking – or I could just remember how this is for roughing work only and how it doesn’t matter all that much and never touch it again 😀

It’s within 0.1mm after a very quick calibration. That’s… rather impressive. Well past my abilities so maybe I really don’t need to do much to this. Have to be careful not to kick the DRO when the machine’s put away mind.

This looks to be where it’s living for now at least – that DRO’s a tad more exposed than I’d like, especially if I’m getting at the tools in the plastic boxes on the left, which is a regular sort of thing (I really could use drawers there but shigata ga nai). Also, the sharpening plates are now riding on top of the thicknesser and an entire crate of finishing stuff is now displaced and living on top of the vacuum cleaner…

It really is getting cramped in here. And no, I have no more wall space left after the latest addition to the wall…

Oh well. On with the project I think. I took the walnut board I was thicknessing last time and fed it through the planer four times, three on one side, one on the other, taking small cuts each time of less than a half-mm.

Hm. Oh yeah. Extraction. 😀

Well, I have a 4-to-2.5-inch reducer in the post and I’ll hook that up to the extraction port when it gets here (and I’ve ordered the bits I need for that mod to do a quick-disconnect on the extraction hood as well). For now, this is manageable – just sweep the cuttings to the floor and then hoover up later.

It’s a shock to see how fast the process is though, not to mention how easy – I mean, you’d be able to keep up with the rate of material removal using a heavy-set scrub plane across the grain if the board was small, but for anything long, this just runs away with it and in terms of effort, it’s not even a comparison. I don’t plan to use it for anything other than roughing, but for taking a quarter-inch off a board in less than an evening’s free time, this thing’s excellent.

The noise is pretty hefty, but I discovered that putting a flat cushion between the thicknesser and the bench did cut down on the really unpleasant bass notes; the thicknesser seemed to have been resonating with the entire shed and the decking outside, which was… sortof impressive? Something to remember for the other machines as well I guess.

Anyway, with the board to rough thickness, out came the #05 and some finish planing was done (the board had bowed slightly in the last week or so because it had been sitting on the bench with one side planed and the other not), and then it was on to edge jointing…

The crosshatching is to watch material removal again. It took a bit of tweaking to get a joint I was okay with, and then a tad more planing of the boards individually to get a nice joint with a spring joint space in it, and then, glue-up…

Should be okay in the morning (the panel will have angled sides so those offsets are fine). The joint isn’t bad but the top will need some work with the plane to get a nice flat surface….

There’s almost a half-mm step there in the middle and we’re flush at the corners. Well, I’ve had worse and this is what hand planes are for…

 

Tools / Woodworking — 4 Comments
04
Aug 18

Toys

Not done a tap in the shed in nearly two weeks now. Between work kicking up a notch and a short holiday away, not been near the place.

You might wish you were here, but it’s hard to know where “here” is…

 

On the way back, I did get to browse around The Carpentry Store for a few minutes, but alas they don’t carry Ashley Iles so I couldn’t try out those dovetail chisels. Mind you, I almost bought a few other things (but I was good…)

 

One day… when I have a bigger shed… it shall be mine…

 

And then there was the shiny shiny…

 

And I now finally understand why people go nuts for Stanley 51s…

This thing is awesome. For the price, it bloody well ought to be, but still. Wow. Solid. Chunky. But just so well balanced, so well put together. Damn nice. Maybe after I win the lotto 😀

And then there were lathes. I mean, even forgetting the fullsize monsters, there were ones that would fit on my bench…

You don’t really grok until you’re facing these just how compact they are. Which is a dangerous place to be when carrying a credit card 😀

But no, I think I’ll hold off on this a little longer because there was something already waiting for me in the mail room in the office. So we returned home, and then this morning junior and I headed into the office via the post office and…

It’s a nice little thing this, just a cheap and reasonably accurate DRO kit. Of course, then I needed something to attach it to, so…

😀

Finally caved in and bought one second-hand from a poster on the UK woodworking forum. A bit of unwrapping later…

And that’s a wee bit larger than even I was expecting.

And holy hell it’s loud. 110dB when cutting wood. I mean, even if you hated your neighbours, you couldn’t do that very often. So this is basically just for when I need to do a lot of hogging off (basically replacing the scrub plane) instead of doing planing per se, and it will live under the bench most of the time (I need to move the sharpening gear, but then I wanted that to be out where I could get to it more readily anyway). I might have to move finishing stuff around a bit though, but hell, that’s life in my workshop. I have to move stuff around if I get a new idea, let alone a new tool. And it works quite well, though I need to get an adapter for the extractor and I’ll have to modify the extractor hood so it’s more readily removable/refittable because it’ll be taken on and off more often than DeWalt though to plan for. There is a mod to do that, I will probably be doing that:

I need to find a way to protect that DRO as well, instead of knocking it off when putting the planer away.

I did think about having a stand to put it (or the mitre saw) on and Lidl were doing a cheap special (which to be honest, looked exactly the same as every other cheap mitre saw stand for half the price) so:

However, given how loud that planer is, I think this is a non-runner. The soundmeter puts it at 110dB inside the shed, and 79dB on the deck outside the shed with the door closed and that’s just too damn loud. I think I can reduce it slightly with more sound baffling on the one surface left that isn’t already covered in baffling or lining:

But I think this is going to be one of those things that only happens for short times at civilised hours like weekend afternoons.

And lastly, the last time I was grinding metal out there for a scratch stock, I noticed a lot of sparks heading towards a lot of flammable things that I was standing in the middle of and at that point I became very cognisant of the distance to the nearest fire extinguisher, so….

Better safe than on fire I say…

← Older Entries
Newer Entries →