17
Mar 20

Hunkering down.

Lots of changes going on at the moment. That’s the nature of sharp transitions – lots of work to get over that step change and then we can settle in. In our case, we’re lucky, mostly we’re having to buy stuff we’d planned to buy over a few months in a few days, set up the home office so both of us can work from there (buying from Ikea instead of making stuff, the horror!) and doing the five million cleanup tasks round the place that normally we can ignore because we’re not here all the time. And the home schooling of course. That’s more a challange because we have to also do day jobs, and the gained time from not commuting every day isn’t quite enough to make up the gap. Oh well.

On the fun side, it does mean a few tools for the shed got bought ahead of schedule (and there might still be one or two more in the next few days depending on how things shake out).

Nothing fancy here, but damn useful…

So now I can do some new things with the lathe. With a bradpoint bit, it just looks like you could make things like cord pulls, but with the fostner bits, you can make little vases and the like.

This wasn’t strictly needed, but it was going for so little and it’s so damn pretty…

What can I say? Tools. They’re a weakness 😀

The hockey pucks arrived as well, and I drilled out a 10mm hole in them, they’ll replace that spacer nut and add some vibration damping into the mix as well.

It’s a bit of a pain to do that job without socket drivers, and I’ve put mine down somewhere and haven’t been able to find them. As usual 😀

Also got that shelf drilled out for all the bits and pieces I have to worry about at the moment (though there’s a wider set of jaws on the way as well, and two new toolrests because that tiny short one is an absolute pain in the fundament when roughing out a spindle. Those 30-year-old record and coronet lathes from the woodworking course have spoiled me 😀 ).

All that stuff would have been ordered over the next 4-5 months, but feck it, our essential supply lines have to take priority right now which means food, medical supplies and equipment and the other essential things. Woodworking tools are not really on that list. And the small companies I’m ordering from could use the cash right now.

Looking a bit tidier now at least, and a couple of calipers arrived as well.

Now I need to figure out how to get 12V out of the power supply for the lathe.

A bit of reverse engineering may be needed here. Or I could use one of the small mains power supplies and just tap into the mains power in here. I don’t want too many mains cables running around the place and batteries are right out.

Last project from the woodturning class. With the schools now closed, that’s the last project from the course we’ll be doing for a while 🙁 But the course may be able to send on homework, and I have all the tools and enough to be getting on with, so as problems go, these don’t even count as problems right now.

The next few months – if not the next year and a bit – are going to be the Interesting Times from the old curse. Humans are creatures of habit and most habits take one to two months to change fundamentally. The odds of this lockdown ending before then seem quite slim; which means on the far side of this, we’ll have an entire global population that has gotten used to working from home where possible, to the idea that the internet is a utility rather than a luxury, that the way we lived up until 1100h last Thursday was not the only way you can live and that all the old “we can’t afford it” reasons given against things like universal free healthcare, universal basic income, flexible working and so on, are all false and always were. Forgiving all student loans in the US would have cost $1.4 trillion and was “impossible” and “ridiculous” before last week. The Americans dumped $1.5 trillion into the market a few days ago to try to stop the dow jones freefall. It bought them 15 minutes of calm before the freefall resumed. They didn’t even ask anyone before doing it. “Impossible” and “ridiculous” were rather laid bare at that point.

And since this pandemic is likely to kill a huge number of people, those kinds of lessons are likely to be copper-fastened into peoples’ minds by tragedy, so the odds of them being rolled back may be lower than the cynic in me thinks.

If so, you’d wonder what else is going to be different in the new world we walk out of this lockdown into.


09
Feb 20

Almost ready to start turning

Two more nights in the woodturning class since last time. And I’m still not dead, which has surprised everyone.

Lay off the jokes, it’s a dibber. You stick it in the ground, wiggle it about to make a hole, drop in a daffodil bulb. The burn lines indicate how far down you’ve gone becuase that matters for some bulbs (specifically, the ones you want to not rot in the ground). Sanding on a lathe btw, is immensely fun, because you just hold the sandpaper and the lathe does the work. Holy hell is that better than sanding a resin&walnut desk….

And then this week….

Yes, that thing was a branch in Marley Park the morning before. Green wood. Fantastic to work with, like cutting cheddar cheese. Woodcarving videos of green wood are now ruined for me, those lads are just cheating 😀

Tapered head…

Turn a handle and put in some burn lines for fun…

Check the fit, refine it a bit…

And that’s it done. And I needed a new carvers’ mallet because I only have two of those and three other mallets (and a few hammers).

And then of course, the part woodturners don’t tell you about…

I’m going to have to figure out how to cope with this in the shed 😀

Meanwhile, the lathe stand progresses. I got the compound cuts in the legs and crossbar done.

Then once that had cured, out of the clamps and out of the shed to get levelled.

First level the MDF on the sawhorses, then level the legs with shims so that the spirit level says flat on both the MDF and the crossbar of the stand.

That’s a wee bit tall to check the spirit level btw, so mirror-on-a-stick came in useful…

So with the legs marked, out with the ryoba and cut to the line and a bit of chisel-paring for the bits where I missed the line, and…

And built up the webs (which were already 3/4″ beech) with offcuts and glue and screws to make that whole area into a solid block for stability.

And it’ll have stretchers under the feet to lock them at the bottom and I can optionally screw the stretchers to the floor if I have to. I might have to, lathes vibrate a lot…

And while it’s still not done (cheers Storm Ciara and having to go vote), I do get to take my new toys to turning class tomorrow night…

Cheap and cheerful set from Rutlands. Now I need to finish the lathe.

 

And maybe get some stuff printed for the shed on the 3D printer, but I’m having issues with that at the moment.

That took almost an hour to clear. Jaysus. And it did it again on the next print so I obviously didn’t get it right either. Le sigh. And that was *after* I’d bought it a new tempered glass bed.

And a new aluminum thingy for the extruder feeder yoke.

It can be a tempermental little bugger, so it can. And it might just be the filament, I’ve heard that some people found this stuff to be a bear but if you bought decent filament all the issues went away. Well, I guess we’ll see…


10
Nov 19

Cleanup

After every long project, the shed is usually a mess – stuff I can’t reach around the piece of work physically to grab and put back in its place, finishing supplies out of their usual storage boxes, sawdust and shavings everywhere, and so on. Stuff you’ll get to when you have a minute. So today was cleandown day after the desk. On with the kneepads, pop out the collapsable garden waste bin (useful little thing that) and I wheeled the bandsaw and sander outside to give room to get all the detritus out, stuff that had built up over the last year or so, including behind and under the workbench and in between the stored wood planks. Long projects are the worst for this sort of thing.

Two hours in, I came to a decision to go through all the scraps and offcuts and get merciless. Anything that was being held onto for bandsaw box material or cutting board material got a careful looking over and if it warped, if it wasn’t large enough realistically, if there was any wane, it all went in the bin. Which is doubly painful for me because thanks to our local government rules, you can’t burn wood in a fire pit outdoors, and we don’t have a woodburning stove indoors, and the local recycling center will take wood but it has a minimum charge for a full carload and one binbag of offcuts costs as much to recycle as a full van stacked floor to ceiling until its suspension cracks. The local bin collection company, Panda, will not accept shavings or sawdust or solid wood in the compost bin or the recycling bin, all of which taken together means that I can pay 80 quid for a cubic foot of walnut, then pay another tenner or so to dispose of the sawdust, shavings and offcuts after the project is done.

This is not an environmentally sound set of policies.

Anyway, after clearing out as much detritus as I could, I started to reorganise things. Small offcuts go in a largish storage box, I returned the paints I’d borrowed as resin dyes to the arts&crafts box for junior, and finally hung my panel gauge and grasshopper gauge up on the wall to try to dissuade myself from letting stuff build up there again.

There are about four small shed jobs lying on top of there already though, an unfinished bandsaw box, a new-to-me saw vice that needs a mounting solution so I can try to finally sharpen and get to grips with my western saws (before I finally call it quits and get a new veritas saw or something), my new-to-me moving fillister plane that needs a better mounting place, and I really need to replace the hasp on the door with that new one. I did at least manage to hang up the heat gun (I know, I know, it has a plug, but do you know how they heated stuff in the 17th century? They set it on fire. That won’t fly here 😀 )

I can actually see the floorboards. I mean, there’s still a mess of finishing stuff round the end of the table, but I could actually stand there. Luxury!

And on the other side, I rearranged all the larger boards I have left, and the smaller ones, leaving stuff I know I’ll want to get to soon towards the front, and generally tidied stuff up.

I think I want to take the dust collection vac and dust deputy solution I have there and build a proper cart for it. It’s all kindof piled up in the corner (along with that box of finishing stuff) and that’s just so damn messy. A cart might actually save me a few inches of room.

And those few inches are pretty critical. If I rebuild the cart for the bandsaw using something other than the 2x4s I knocked this one up out of, I might regain just enough space that using the vice is no longer very awkward…

Even getting those storage boxes out from under the vice is a pain because of two inches of protrusion by the cart. Make it over, make it a bit tighter, might get that space back.

Of course, first I want to finish the tidying up…

…and then there are just a few projects to dive into, like hooking the thicknesser up to the dust collection…

…and I have a few projects in mind after that as well…
…so yeah, I might get to the cart sometime next year. Or after that. Such is the way these things go 🙁