Woodworking

Cheese Press / Shed / Sidecar Cot / Woodworking / Workbench — No Comments
08
Oct 16

Twenty

So the early start plan kinda went to pot because of other duties, but I did manage to get to woodies and get another tin of the willow colour of paint to do the second coat on the shed. And then, annoyingly, got the second coat out of the remainder of the first tin. Gah. Oh well, I’ll find something for it. Meanwhile the shed’s looking okay, but I didn’t manage to get the first coat of the cream colour on it, so that might make getting everything finished tomorrow a bit of fun.

img_9443a

img_9449a

Can’t say that it looks like a massive difference with the second coat, especially as the colour darkens very noticeably on drying, but this stuff really does need the second coat when you look at it close up.

Then on to getting the cheese press done. I picked up the needed bits of threaded rod and such at woodies while getting the paint.

img_9456a

The threaded rod will get cut into 1′ long sections to form the two side supports and the main screw and the various washers and nuts will secure it (the hooks are for my bench brush which is in need of a better home than hanging on the quick-release of the vice).

img_9457a

The more difficult part of this has been getting a 2×2 chunk of wood down to something that vaguely looks like a handle if you squint and are blind. I was able to saw out a big chunk of the waste, and carve the basic shape very roughly with the gouges, but trying to get it even close to smooth was being a pain so out came the spokeshave, which promptly tore the crap out of the surface no matter how I twiddled with it. So I took a tip from Richard Maguire’s spoon rack series, took off the adjustment knobs completely, and set it by keeping the base flat on the bench and letting gravity put the blade in contact with the bench, then tightening the clamping screw. And it worked like a charm. It went from biting and skipping and destroying the face of the wood to looking like an actual woodworking tool being used by someone who was competent. Not sure how it managed that last bit, but I wasn’t complaining much. Before long I had an ugly lump-shaped chunk of tree branch and figured I should stop before I broke it too badly.

img_9466a

Some butterfly nuts on the two side supports to cinch the crossbar on to the top of the cheese vessel, and a chunk of wood on the bottom of the screw to push against a plate in the cheese vessel and that’s your cheese press, more or less. First, some nuts needed epoxying and there was a small void to fill on the face of the board.

img_9467a

Tomorrow I’ll clean up the boards and get them flat and shellac them, add the block on the end of the screw and I think that’ll be it finished. It’s not a very fancy thing after all. I’d like to put some springs on the side bits of threaded rod, but I couldn’t find any. Oh well, easy retrofit.

Of course, that last spokeshave session had a casualty…

img_9459a

I know I said I’d make a hardwood vice face later on, but I think it might be sooner than I thought. I re-screwed it on, but I don’t want to glue it and I’m not sure those two screws are going to last. I’ll have to think about this one.

First though, on to resawing ash for slats. One or two of the resawing boards tonight were pains in the fundament with the blade wandering out of nowhere, but I was able to use the disston to get the line back on track and finish the cut without losing a board. Which let me write a very nice number indeed…

img_9462a

20 slats out of three boards, with another three definitely unusable and another one as a very marginal call (ie. use it if we really need just one). That’s all the original plan called for. I don’t doubt I might find I need another two or four more, but I’ll try not to 😀

img_9464a

img_9465a

In case anyone was wondering, yes, you can resaw 1″ thick 8″ wide ash boards by hand, and it’s not actually the most strenuous job in the world… but it’s not a lot of fun either really, and it can be finicky keeping the blade from wandering. As soon as I’m able to house it, I’m going to get a bandsaw.

Now, for the coming week, it’s planing in the thicknessing jig to get those 20 slats all down to size…

2016-09-25-12-20-38a

Cheese Press / Shed / Sidecar Cot / Woodworking — 2 Comments
07
Oct 16

Untitled

So the weekend weather is forecast to be dry, and since I was stuck working from home because of the luas breaking down this morning:

luasbreakdown

I thought I might as well get a head-start on the shedwork by painting it. We’ve been planning to do that for a while and painted some parts to test what we thought of the colours and decided on a colourscheme, so I took out the sander, removed enough of the test swatches to get a good key for the paint and got out the masking tape.

img_9398a

It’s not a bad little shed, but it’s a bit dingy. After a decade, the wood preservative stuff is just not really going to cut it for much longer, so a decent coat of paint should give it an extra year or two. So on with the first coat for the trim parts (trim’s really the wrong word I think, there’s such a small wall to trim ratio).

img_9405a

Looks better already. Pain in the fundament keeping those bushes on the left wall off the left wall while painting, mind you. Not looking forward to that bit.

Then after dinner, went out to look at the new toys that arrived in the post.

img_9410a

The chisel was an accidental win on ebay, I already had a set of three that would do, but had forgotten a bid on this and it won. Hey, for a fiver, I’ll take that.

img_9415a img_9416a

Bevel’s clean, no nicks on the edge, back could stand five minutes of lapping on the stones, but I don’t think I’ll even need the 80-grit paper for this one. Nice.
The saw file is equally nice, and needed if I’m going to sharpen these saws properly. Thing about a saw file is, it isn’t a triangular file, it only looks like one. Look closely at those “corners” and you discover they’re just very narrow flat edges with teeth:

img_9419aApparently it’s become quite hard to get really good saw files anymore, on a worldwide basis, which is a bit worrying as it’s not a tool to use itself, but as a support tool for a pretty basic tool – the saw. If you can’t sharpen a saw anymore and you’ve lost the industry for making the tooling you need to do that, then you’ve lost the ability to make a decent saw, and that’s a pretty basic tool for a civilisation to lose…

img_9422a

And then there’s these guys. See, I already have a countersink bit set, they’re the ones that look like this guy:

img_9423a

So if you’re buying a countersink bit, don’t buy one of these, they’re awful. They vibrate all over the place when you’re using them – power drill, eggbeater, brace, makes no odds – and they make a horrible mess of the wood. I suspect mine are cheap and unsharpened, but still, I paid about as much for them as I did for the new ones, and the new ones don’t vibrate at all. And as to the finish… well, here’s the old one:

img_9427a

And here’s the new one:

img_9424a

Same hole, different sides of the same scrap, in the same drill chuck at the same speed and pressure. Utterly night and day. The newer ones cut clean and burnish at the same time, smoothly without fuss. The older ones, it was like I had a hammer action on the drill and it was turned on, and it didn’t so much deburr as burr. Those bits are for the bin, and the new ones are very recommended in their place.

Then on to the cheese press. I took the base out of the clamps and had a look at it.

img_9428a

And then noticed I’d let one end get misaligned by a mm or so during clamp-up. Bother.

img_9429a

So, out with sid, and after a moment of pondering, got one of the slats from the cot that I rejected and used it as a thin batten for a planing stop.

img_9431a

I gave the board a few swipes with sid and that mm was gone in less than twenty seconds. I then switched to the jack and got that top face with the figure flat, squared an edge and got the other face flat and parallel, and then rounded over the edges. Then I did the same for one of the other resawn boards that will form the top clamp. And found I had some nice grain pieces to show off.

img_9434a

img_9433a

Then I considered the handle for the screw. 

img_9435aWorkholding was nice and easy, and then it was a lot of paring with chisel and gouge (Hey Daniel! I made something with that birthday present! 🙂 ). It’s not overly complex – and it’s not done yet either – but it looks like it’ll do the job.

img_9436a

I left it there for the press for now, I need some metal bits from woodies or chadwicks tomorrow to finish it off and then there’s the actual finish to do (I have some shellac I’ve been looking to experiment with, or I could try using the soap finish I’ve been reading about. Choices, choices…)

img_9438a

I did get some crib work done tonight as well – I now have 14 slats down, six to go – but the resaw was a pain and nothing seemed to go easy, so I knocked off at that point rather than make a mess out of a nice piece of ash because I was tired.

Cheese Press / Sidecar Cot / Woodworking — No Comments
06
Oct 16

Pressing diversions

Someone at work asked me today if I could make a cheese press (perfectly ordinary question). At first I thought they meant something a bit fancy like one of these:
cheesepresss

Which is doable, but a little time-consuming and I have about six other things on the go at the moment, but then they explained no, they meant like this one:

cheesepress1

Now that’s all pretty and stuff, but basically it’s two planks, three bits of threaded rod, a few nuts and a handle. How hard could that be? So I said I’d have a go. I had some offcuts of 2x4s from the bench that were around a foot long and the cheese jar thingy they had wasn’t that big, so I figured this could be reasonably easy…

img_9372a

Few small offcuts – I figure resaw the 2x4s to 4x1s, glue up two for a panel for the base, use one for the crossbar at the top and take that 2×2 and get a handle out of it. If nothing else, it’ll be some practice with chisel and spokeshave that’ll be handy for the crib later. So I clean them up on a face and edge with the jack and mark off a mid-line for the saw and get going.

img_9374a

I’ll say this much for pine – it’s a pain for knots or fancy joints, but it really does saw easy.

img_9380a

Mind you, helps to have a good saw. Today, this thing was a line-following machine…

img_9381a

Did I mention how critical that wedge was though?

img_9383a

Okay, nice clean resawn boards. With a pretty knot-pattern too.

img_9386a

Must try to keep that in as a feature, it’s too nifty not to. Resawed the other board as well, then took the first two and bookmatch planed the edges for a butt joint and gave them another swipe with the smoother to spring the joint, and glued up.

img_9388a

Look, I know the glue brush is a fancy gadget, but screw it, it works better than looking for scraps of timber all the time and the glue peels right off when it’s dry. I like the thing. I’m a little worried that the bristles won’t last and they’ll come off as I pull dried glue out of them, but meh, I can live with it. The other end, the glue paddle thing, is the normal primary school glue spreader design and you can get packs of 50 of them for pennies on ebay if it comes to it.

img_9389a

Hmm. I think the alignment drifted by a mm or so during the clamping. Or the kerf was wider than I thought. Oh well, still not too shabby.

img_9378a

And some very rudimentary roughing out for the handle. More work there yet, but I want to get the nuts and threaded rod and stuff before doing too much, so I know what size the holes will be and where they’ll go exactly. So I set it all aside there for the moment and went back to the slats for the crib and marked up the blanks for resawing.

img_9393a

At that point I drew a line under it. Only an hour in the shed (late start), but I might get that press done over the weekend. Have the electrics to do as well though, and the weather is finally forecast to be dry enough to paint the shed. Might have to make that the priority, there won’t be many opportunities between now and winter to get that bit done.

← Older Entries
Newer Entries →