Properly bent

Right, Saturday morning so on with steambending the second upright.

img_0034a

Mise en place all done. Now, on with the polythene tube…

img_0039a

And now put the compression strap in place, clamp it at one end and get the “start bend here” line matched up with the initial straight part of the jig.

img_0040a

I’ve just clamped the end block here temporarily, I’ll remove those before steaming and reclamp them before bending (I want the excess water to be able to drain out of the tube readily, and it can’t do that when the end is pinched by the clamps).

img_0041a

The idea here is to prevent that end block from twisting out and away from the piece because if it does, the compression strap won’t be in compression and the outside of the piece will splinter.

img_0044a

And steam on!

img_0047aUnder covers, though, because it’s bloody cold out and that’ll suck the heat right out of the piece which is not going to help things.

Now, while that steams for two hours, on to the next job, the large top panel in the bottom box part of the crib.

img_0049a img_0050a

Four feet by one foot of rough-sawn ash with a bit of twist in the second board. That’s rather a good lesson in “why we invented powered planer/thicknessers”

Two hours (and some tea) later, it’s time to bend…

img_0052a

The handy thing (well, amongst several things) about this method is that the bend doesn’t have to be done in under 20 seconds. This took nearly 20 minutes in total. First off, ensure the two end blocks are all clamped firmly in place.

img_0057a

And then it’s just musclepower to grab the piece and pull it to the form, adding the clamps as they fit (and towards the end, you pull the piece in using the clamps, just slowly turning the handle to crank the piece in). img_0055a

And make sure the interim points are pulled in as well.img_0059a

And note that the steam’s still going during all of this. And you leave it going for a while longer (and you put the covers back over it when it’s bent fully too). In this case, it got another half hour or so before the water ran out and then everything stayed on the jig cooling off (under covers so that it didn’t cool too fast) for another two hours, and then all the clamps come off and the piece comes out of the poly tube.

img_0060a

This is annoyingly good. Annoying because there were no splinters or cracking, which means I now have one upright that was perfectly bent and another that was imperfectly bent. Do I match the two or do I bend a third and use #2 and #3? It’d cost another week…
img_0062a

No splintering but some deformation of the surface because I forgot to put the leather between the compression strap and the piece. There’s always something. Well, we’ll let it dry for a week and do some spokeshave work and decide then I guess. Meanwhile, time to take it from the overbent 105 degrees to the final 90 degrees on the drying form.

img_0064a

One clamp to start, crank it in a bit and let the two ends slide as needed, then add more clamps to tighten everything up.

img_0065a

It’s a pretty good fit to the curve so far. Only minor gaps.

img_0070a

And the form isn’t 100% perfect itself, so this is good enough. And the measurements of the piece match within a few mm to the earlier piece.

img_0076a

Now I guess we just wait for the new piece to finish drying and then do proper comparisons and see if we can get these two to match and use them. They’re both tall enough at least. Now, back to finishing off the top panel…

img_0077a

Okay, that’s way too large and too much work to do for planing. Time to rough-cut it down to closer to the final size.

img_0081a

img_0086a

And that’s a bit more manageable. I’ll finish this off tomorrow. And then there’ll just be another three ash panels and one drawer front to do. Yeesh.
And then there’s the frames to put them into as well, but I can’t really tackle those until I have the uprights as they form two of the four vertical frame pieces (there’s a fifth but it’s not involved in the panel layout).

I was reading through Schwartz’s The Anarchist’s Toolchest over the last few weeks, there’s a neat trick he does for frames and panels in the toolchest that I might steal for here, which is to cut two grooves in the frame and the panel pieces instead of one groove and one tongue – then you offset the panel towards the outside of the box and the side wall of the panel’s groove acts as the tongue to the frame’s groove; and the other side wall of the panel stands proud of the frame. And in this case, I’d plane a bevel around the edges of the panels to give a 3-D effect. Have to get the #40 plane up and running for that though, and it’s currently got some corrosion issues…

 

Tags: , ,

2 comments

  1. I think you are better off to reuse parts of the splintered, cracked one(s) for something else and steam bend another. It looks like got the procedure working as it should. And I will never again complain about how small my workshop is.

  2. […] And it was also where all the gardening stuff was stashed (I’ve since moved that to a storage box outside). There’s a small decking area just outside the shed which has proven useful for some tasks like assembly and in-a-bag steambending: […]

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.